Electrical Components
Catalog Pages are provided in Adobe Acrobat™(.PDF) format.
|
|
The Progressive EC Junction Box design interfaces with SPI Class C 24 VDC PLC's and eliminates loose wire connections to the press. The fused power circuit protects the programmable logic controller from damage, while using common signal names. All connectors are housed in a rugged aluminum die cast box which mounts to the platen. |
N/A
|
|
For an alternate mounting system where space is limited, bendable Mounting Brackets are available. |
N/A
|
|
Progressive Junction Box Cables include a color-coded wiring schematic with commonly used signal names. |
Junction Box Cables
N/A
Progressive
Patch Cables
are fully assembled,
color-coded, and keyed to be function specific. Easy connection and
disconnection through a positive push/pull quick disconnect.
Patch Cables
N/A
Progressive Jumper Plugs, commonly
referred
to as "dummy plugs", provide return signals to
PLC's when return signals are required. The fully assembled plugs
attach directly onto the screws supplied on the Junction Box to
prevent loss
during mold changes.
Jumper Plugs
N/A
|
|
Progressive Recessed Connectors protect receptacles from damage
during transport. Connectors are color-coded and keyed for the |
Recessed Connectors
Switches
|
|
Progressive KO Switches verify ejector plate position before the next controller sequence. BCP Mount style features a compact design which houses both switch and connector in the bottom clamp plate. |
Progressive Single Ejector KO Switches verify ejector plates are back before the next controller sequence. Ejector Mount style features a compact design which houses both the switch and connector in the ejector plate.
Single Ejector KO™ Switch
Dual Ejector KO Switches verify ejector plate position before the next controller sequence. Ejector Mount style features a compact design which houses both the ejector back and ejector forward switches. These are integrated into a single connector which plugs into one position of the EC System Junction Box.
Dual Ejector KO™ Switch
Progressive
CamAction® Switches verify that
the slide carrier is fully retracted before the next controller
sequence. Available with or without receptacle, depending on
position of CamAction
within the mold.
CamAction Switch
The Progressive Plate Position Switch verifies plate location before the next controller sequence. This houses both the switch and connector in a compact design, machinable from parting line.
Plate Position Switch
The Progressive Side Action Switch can be mounted externally, partially, or fully pocketed to verify slides are back before next controller sequence. The rugged construction protects switch and connector from damage.
Side Action Switch
The Progressive External Mount Switches are designed for plate position with the Enable function or the Core In/Core Out function.
External Mount Switch
|
|
Progressive Extension Block Assembly and Extension Pins attach to Side Action Switch #SWSA-100 to extend the reach of the switch actuation. |
|
|
Utilize the External Actuator Block to mount the External Switches on parting line. |
N/A
|
|
New BX Series Hot Sprue Bushings are manufactured to standard sprue bushing sizes
and are designed to replace existing cold sprues, replace inefficient
hot sprues, or feed into runner systems. This unique bushing with its full length thermally conductive core
and nickel plated tip eliminates uneven heating problems, keeping
the melt temperature consistent throughout the bushing. |
|
|
Wire Channel Inserts protect wires for hot sprue bushings, cavity pressure transducers, etc. Easy installation by press fitting insert into milled channel. |
|
|
Progressive Variable Depth Thermocouples (Spring Style) allow adjustment to a variety of depths needed per application. Pinouts are color coded and keyed specifically to match the Junction Box. |
|
|
Progressive Cavity Pressure Transducers monitor injection pressure within the mold. These assemblies can directly replace other transducers and include a recessed connector for permanent installation into the mold. |
CPT - Button Style
CPT - Flat Style
|
Injection Mold
Components |
Unit
Inserts | Electrical
Components |
ENTIRE WEB SITE CONTENTS ©2010
PROGRESSIVE COMPONENTS INTERNATIONAL CORPORATION